Best Skid Steer Snow Blower: How to Choose the Right Farmry Model

The best skid steer snow blower is the model that matches your loader’s hydraulic system, fits your clearing route, and handles your typical snow removal workload. The widest attachment is not automatically the right choice, and more hydraulic flow is not automatically better.

Farmry’s skid steer snow blower attachments include the SSB60, SSB72, and SSB84. Their different sizes give buyers a starting point, but choosing between them requires more than comparing model numbers.

Start with the site, confirm hydraulic compatibility, then compare dimensions, attachment weight, chute control, and service requirements. That approach helps you select equipment for the work you actually need to complete throughout winter.

Define Your Snow Removal Job First

Where Will You Clear Snow?

Residential driveways, parking lots, and access lanes present different constraints. A wide, open lot provides room for overlapping passes. A driveway between buildings may leave little clearance beside the blower, even when the skid loader itself fits.

Measure entrances, turns, and the narrowest section of your route. Include parked trucks, curbs, walls, and other obstacles that reduce usable space. Sidewalks require particular attention: a machine that reaches the entrance may still be too wide for the working path.

Also decide where the snow will go. A snow blower moves snow through a chute toward a discharge area. A snow pusher or angled plow primarily pushes it toward a pile. A bucket can serve a separate loading task. Choose among these skid steer attachments according to the required result, not just attachment width.

What Snow Conditions Do You Usually Face?

Light snow and wet snow place different demands on equipment. Heavier snow increases the material load entering the blower, while hard-packed snow can create more resistance at the auger.

Record whether your route usually involves fresh snowfall, packed snow from vehicle traffic, or refrozen piles. Do not assume an attachment approved for snow clearing is also approved for breaking solid ice. Compacted snow and frozen slush require assessment rather than a promise that one machine will handle every condition.

Match Hydraulic Flow Before Comparing Width

Check the Loader and Attachment Together

A skid steer snow blower uses the loader’s auxiliary hydraulic power. Engine horsepower alone does not establish compatibility.

Check these items against the requirements for the exact blower configuration:

• Auxiliary flow rate, usually expressed in gallons per minute.

• Operating pressure and the attachment’s permitted limits.

• The loader’s selected hydraulic operating mode.

• Couplers, return connections, and any other specified circuit requirements.

• Mounting compatibility and the loader manufacturer’s attachment restrictions.

A familiar mounting plate does not prove that the hydraulic system is suitable. Likewise, an attachment’s horsepower range is only one part of the match.

Confirm the approved continuous hydraulic flow and pressure with Farmry before ordering. Resolve any differences between a listing and the applicable technical documentation rather than selecting the more generous number.

Standard Flow and High Flow Are Not Interchangeable Approvals

If you are searching for a low-flow skid steer snow blower, compare actual specifications instead of relying on the label. Standard-flow and high-flow descriptions do not establish one universal operating range across all machines.

Do not switch a loader into high-flow mode simply to improve performance. A high-flow-capable machine may offer more than one setting; the selected setting must suit the attachment.

Too much flow is not a substitute for correct matching, and pressure settings should not be increased to force the blower through resistant material. Reliable performance starts with an approved combination, not the assumption that more power always helps.

Choose a Width That Fits the Loader and the Route

Compare Track Coverage With Available Clearance

A clearing path that covers the loader’s tire or track footprint can help avoid driving over uncleared snow. However, choosing a blower wider than the machine is not a rule that overrides hydraulic compatibility, handling limits, or access restrictions.

Measure your loader’s actual outside width, including its installed tires or tracks. Then check the blower’s effective working width and overall dimensions.

The nominal size in a model name is not a substitute for either measurement. Housing panels extend beyond the snow-handling opening, so a “72-inch skid steer snow blower” needs more than a 72-inch opening for the entire attachment to pass through.

Wider Coverage Must Still Be Manageable

A wider cut width can reduce the number of passes across large areas and improve efficiency, provided the machine can process the incoming snow at a suitable travel speed and maintain good handling. That benefit can disappear when a wider blower forces slower feeding, difficult turns, or repeated repositioning.

Attachment weight matters too. Evaluate the blower against the loader manufacturer’s operating-capacity and attachment guidance, while matching width choices to the loader’s machine size and capacity and accounting for the complete installed configuration. Net weight, shipping weight, and usable operating capacity are different measurements.

On uneven terrain, width and weight are only part of the decision. Ground support, traction, visibility, and the machine’s operating limits still govern where you can work.

Compare Farmry SSB60, SSB72, and SSB84

The following specifications help narrow the options. Nominal sizes are the product designations, not guaranteed effective clearing widths.

These are product-page figures for comparison. Confirm the supplied version, effective working width, and complete hydraulic requirements before making a fit decision.

SSB60: Start Here When Access Limits the Choice

The SSB60 is the narrowest of these three options. It is worth evaluating where entrances and maneuvering space limit a wider attachment.

However, narrower does not mean suitable for every small loader. Its listed 940-pound net weight and mounting requirements still need checking. Check the complete attachment approval, not only whether the loader can lift its weight.

SSB72: Evaluate the Middle Width Against Your Route

The SSB72 offers a middle option for buyers comparing snowblowers for skid steer loaders. Check whether its overall width fits the route and whether the loader meets all attachment requirements.

Its position between the other models does not make it a universal compromise. A restricted entrance can rule it out, while a different loader configuration may change the hydraulic or handling assessment.

SSB84: Consider Wider Coverage for Open Work Areas

The SSB84 provides the largest nominal size in this group. It is a candidate for open parking lots and broad clearing routes when the loader and site support its dimensions and weight.

Do not choose it solely because the property is large. Frequent narrow turns, heavy wet snow, or an incompatible hydraulic setup can outweigh the benefit of wider coverage.

Evaluate Snow Handling, Chute Control, and Surface Contact

Understand the Auger and Impeller

Farmry describes these models with a serrated steel auger and a separate impeller. For frequent commercial snow removal, heavy-duty construction matters most for long-term durability. The auger gathers and feeds snow; the impeller discharges it through the chute. Farmry also highlights certified American steel and durable materials built to withstand harsh winter conditions. This two-stage arrangement gives the components different jobs. Reinforced housings also improve durability in harsh conditions.

It does not establish that every type of packed snow or ice can be processed safely. Auger design, impeller operation, hydraulic matching, and the incoming load must work together.

Match travel speed to the material entering the housing. In heavy or wet snow, slow down as needed to avoid overloading the blower. If snow stops discharging or the attachment jams, stop and follow the shutdown and clearing procedure. Never reach into the auger or chute. Hardened wear components can also reduce maintenance needs over the season.

Choose the Chute Control You Need

The three product listings specify manual 360-degree chute rotation, with electric control available as an option. Manual rotation describes the adjustment range; it does not mean every direction is safe for discharge.

Aim away from people, vehicles, buildings, and areas you have already cleared. Consider wind and the available storage space before beginning a pass.

For an upgrade, review the electronic chute rotator and deflector kit. Confirm compatibility, installation requirements, control placement, and availability for your equipment. Do not assume a hydraulic rotation kit is included with the standard blower.

Farmry’s manual, electric, and hydraulic chute-control guide explains the control options in more detail.

Set Skid Shoes for the Surface

Adjustable skid shoes change the clearance between the blower and the ground. Their setup matters when moving between pavement, gravel, and other surfaces.

On gravel, the objective includes limiting stone pickup. On sensitive surfaces, inspect the cutting edge and shoes for wear or damage that could mark the ground. Neither adjustable shoes nor a new cutting edge guarantees damage-free operation.

Follow the approved setup for your surface. Do not use loader down pressure to compensate for incorrect adjustment or force the attachment across an obstruction.

Make the Final Choice Before Ordering

Compare the Complete Setup, Not Just the Price

When reading skid steer snow blower reviews, look for the host machine, hydraulic setup, snow conditions, and attachment configuration behind each opinion. A result from another operator does not prove compatibility with your loader.

Compare the regular price or current offer against the full configuration you need. Include approved controls, mounting components, delivery arrangements, and service parts where applicable. Spending less money on the attachment alone does not establish the lowest total cost.

For durability, examine documented components and service access rather than broad claims about robust construction. A powder coat finish helps resist corrosion and moisture during winter use. Cutting edges, skid shoes, hoses, and drive components need inspection and appropriate replacement even on equipment designed for winter use.

For example, consider a route with an open parking area followed by a narrow driveway. First eliminate models that cannot pass through the tightest opening with suitable clearance. Then compare the remaining options against the loader’s approved hydraulic and attachment limits. The broadest part of the property should not determine the choice for the entire route.

Where every clearing area is open, a wider skid steer blower may deserve closer consideration. Still, compare the work under your usual snow conditions, including the time needed to turn and reposition.

Use a Short Compatibility Checklist

Before you order, record:

• Your loader’s model, installed configuration, and outside width.

• Auxiliary hydraulic specifications and the intended operating mode.

• The blower’s confirmed working width, overall dimensions, and weight.

• Mounting, connection, and chute-control requirements.

• The narrowest access point and available discharge areas.

• The parts and service support needed during the snow season.

Send unresolved fit questions to Farmry’s equipment support team. Choose the model only after the critical requirements agree. That is a stronger basis for selecting the best skid steer snow blower than width, horsepower, or price alone.

FAQs

Can a skid steer snow blower fit a mini skid steer?

Not automatically. A mini skid steer may use a different mounting interface, hydraulic circuit, and attachment-weight limit. A physically connectable blower is not necessarily approved for operation. Some snow blower attachment options are also built for tractors and other equipment types, but that does not confirm fit for a mini skid steer. Confirm the complete combination with both equipment manufacturers before using an adapter or assuming a smaller SSB model will fit.

Can I replace a broken shear bolt with a stronger bolt?

No—not unless the manufacturer specifies that replacement. A shear bolt is part of the attachment’s protective arrangement, not simply a fastener to upgrade. Use the specified part and investigate the cause of failure. Increasing bolt strength can defeat the intended protection rather than solve the underlying problem.

Will a snow blower throw wet snow as far as light snow?

Not necessarily. Throwing distance depends on snow condition, incoming load, wind, chute position, and equipment setup, and while the blower is designed to blow snow efficiently, it may not throw wet snow as far. A published distance is not a guarantee for wet snow. If discharge deteriorates, follow the operating instructions rather than increasing hydraulic flow beyond the attachment’s approved limits.

How should I store a skid steer snow blower between winters?

Clean, inspect, and service it according to the applicable instructions, then store it in a dry, secure location with proper support. Address worn parts before the next season. Use the Farmry operator’s manual library for model-specific lubrication, storage, and return-to-service checks.

Does the warranty cover normal wear on snow blower parts?

Generally, normal wear is different from a defect in materials or workmanship. Coverage depends on the applicable terms, use, and issue—not simply the age of the attachment. Review Farmry’s warranty policy before assuming a worn component qualifies for replacement.